Rat sE-selectin ELISA kit instruction manual
2021-05-31 01:28:11
Shanghai Xitang Biotechnology Co., Ltd. 021-55229872, 65333639
Rat sE- selectin ELISA kit instruction manual
 ( used in serum, plasma, cell culture supernatants and other biological fluids )
principle
This experiment used double antibody sandwich ABC-ELISA. The anti-rat sE-Selectin monoclonal antibody was coated on the plate, the sE-Selectin in the standard and the sample was combined with the monoclonal antibody, and biotinylated anti-rat sE-Selectin was added to form an immune complex attached to the plate. On the horseradish peroxidase-labeled Streptavidin combined with biotin, the substrate working solution is blue, and finally the stop solution sulfuric acid is added, and the OD value is measured at 450 nm. The concentration of sE-Selectin is proportional to the OD value, which can be passed. Draw a standard curve to determine the concentration of sE-Selectin in the specimen.
Kit composition ( 2-8 ° C preservation)
Coated Wells | 96 holes | Enzyme Conjugate | 12ml |
10× specimen dilution (Sample Buffer) | 12ml | 20×Wash Buffer | 50ml |
Standards: 400ng/bottle | 2 bottles | Substrate working fluid (TMB Solution) | 12ml |
Primary antibody working solution (Biotinylated Antibody) | 12ml | Stop Solution | 12ml |
Prepare reagents and collect blood samples
1. Collection of specimens: serum, plasma (EDTA, heparin anticoagulation), cell culture supernatant, tissue homogenate, etc., as soon as possible, stored at 2-8 ° C for 48 hours; longer time must be frozen (-20 ° C or -70 ° C ) Save to avoid repeated freezing and thawing. Serum and plasma should be diluted at least 1 : 2 (take 50 ul, add 50 ul of the diluted solution, dilute 2 times).
2. Standard solution preparation: Add 1ml of distilled water before use and mix well to form a 400ng/ml solution. Set the standard tube 8 tube, the first tube plus the standard dilution 900ul, the second to the eighth tube to add the sample dilution 500ul. Add 100 ul of 20 ng/ml standard solution to the first tube, mix and aspirate 500 ul with the sampler, and transfer to the second tube. Repeat the dilution as described above, and remove 500 ul from the seventh tube and discard it. The eighth tube is a blank control.
3. The 10× specimen dilution was diluted 1:10 with distilled water (example: 1 ml concentrated dilution + 9 ml distilled water).
4. Washing solution: diluted 1:20 with distilled water (example: 1 ml concentrated washing solution added to 19 ml of distilled water)
Test procedure
1. Loading: Add 100 ul of standard or sample to be tested in each well. Mix the reaction plate thoroughly and let it stand at 37 °C for 120 minutes.
2. Wash the plate: Wash the plate thoroughly with washing solution 4-6 times, and dry it on the filter paper.
3. Add 100 ul of the first antibody working solution to each well. The reaction plate was thoroughly mixed and placed at 37 ° C for 60 minutes.
4. Wash the board: the same as before.
5. Add 100 ul of enzyme-labeled antibody working solution per well. The reaction plate was placed at 37 ° C for 30 minutes.
6. Wash the board: same as before.
7. Add 100 ul of substrate working solution to each well and let it react at 37 ° C for 15 minutes in the dark.
8. Add 100 ul of stop solution to each well and mix.
9. Measure the absorbance at 450 nm using a microplate reader within 30 minutes.
Result calculation and judgment
1. All OD values ​​should be subtracted from the blank value before calculation.
2. Using standard products 40, 20, 10, 5, 2.5, 1.25, 0.625, 0 ng/ml as the abscissa and OD as the ordinate, plot on the coordinate paper and draw the standard curve.
3. Find the corresponding sE-Selectin content on the graph based on the OD value of the sample, and multiply by the dilution factor.
Kit performance
1. Sensitivity: The minimum sE-Selectin assay concentration is less than 3.2 ng/ml.
2. Specificity: Recombinant or natural rat sE-Selectin can be detected simultaneously. Does not cross-react with other cytokines in rats.
3. Repeatability: The coefficient of variation in the plate and plate is less than 9.7%.
Precautions
1. It is recommended to make double holes for the above standard holes and samples to be tested. The standard curve should be made at the same time for each measurement.
2. The washing process is critical. Insufficient washing will result in an accuracy error and an erroneous rise in the OD value.
3. After the slats are opened, the remaining slats should be sealed again to keep the slats dry .
4. This kit should be stored in a 4oC refrigerator.
5. This kit is for scientific research only and cannot be used for clinical diagnosis!
We are the one of three leading factory in China, specialized in manufacturing laser distance module since 2004. Bilateral laser distance measurer is one of mutifunctional laser distance device. JRT multifunctional laser measuring device functions include area,distance,length,volume,continuous measurement,addition and subtraction, measuring unit: ft/m/inch. More functions can be customerized. And the laser measuring meter have distance 30/40/60/80/100/150m for chosing. This bilateral degin is our 40m middle laser distance transducer 703A laser measuring meter.
OEM service:
* usb chargable
* voice
* IP54 rating
* Colorful case
Laser Range Finder Measurer，80M Laser Distance Meter，Distance Meter 80M，Laser Distance Meters
Chengdu JRT Meter Technology Co., Ltd , https://www.cdlaserdistancemodule.com